Two-Component Cold Applied Liquid System for Roofs, Balconies and Car Parks - IKO Metatech - Liquid Applied Waterproofing

IKOpro Bonding Agent.

Guidance for specification option:

IKOpro Systems Bonding Agent (black) is a specially formulated primer. Enhancing the properties of self- adhesive bitumen roofing membranes, it promotes strong bonds even at temperatures as low as 5°C.

IKOpro Sprayfast MPP.

Guidance for specification option:

KOpro Sprayfast MPP (Black, Multipurpose Primer) is a

specially formulated high performance bonding primer.

It allows the speed of application of the bonding primer

to be five times faster than conventional bitumen primers,

promoting strong bonds at temperatures as low as

5°C. For self adhesive and torch applied bitumen membranes.

IKOpro Quick Dry Primer.

Guidance for specification option:

IKOpro Quick Dry Bitumen Primer (black) is a fast-drying bitumen priming solution for torch applied bitumen membranes.

IKOpro Bonding Agent.

Guidance for specification option:

for self adhesive bitumen membranes only

IKOpro Sprayfast MPP.

Guidance for specification option:

for self adhesive and torch applied bitumen membranes

IKOpro Quick Dry Primer.

Guidance for specification option:

for torch applied bitumen membranes

IKO Ultra S-A Air and Vapour Control Layer.

Guidance for specification option:

Self adhesive for combustible substrates

S-A VCL (Self-Adhesive) is a high performance vapour barrier for use in adhered IKO Polymeric systems. It is composed of a polyester reinforced aluminium core, coated with a rubber modified, self-adhesive bitumen coating. The membrane is protected on the underside with a release film backing and coated on the top surface with a fine mineral finish. A selvedge of 75mm width, protected with release film, provides a quick means of completing side laps.

IKO Ultra T-O Air and Vapour Control Layer.

Guidance for specification option:

Torch applied to non combustible substrates only

T-O VCL (Torch-on) is a high performance vapour control layer for use in adhered IKO Polymeric systems. It comprises an impervious aluminium core, reinforced with polyester and coated with a specially formulated quick melt SBS modified bitumen. The lower surface has a sacrificial film which rapidly melts during the torching operation.

Unilin Alu Insulation, 2400 x 1200 mm.

Unilin Alu Insulation, 1200 x 1200 mm.

Unilin MG, 60 mm thickness.

Unilin MG, 120 mm thickness.

IKOpro PU bonding adhesive.

IKOpro Sprayfast IBA.

IKO Ultra H-A Underlay.

Guidance for specification option:

IKO Systems H-A underlays are polyester reinforced bitumen membranes used as underlays within a built up roofing system, The membranes are coated on both sides with self-adhesive bitumen SBS elastomeric coating. They have a fine mineral upper surface with a 75 mm release film selvedge to facilitate rapid installation of lap joints. Size: 1 x 16 m.

Bonded by heat activation to primed insulation board (laps heat welded).

IKO metatech waterproofing.

Guidance for specification option:

A two-component coating based on methacrylates that cures after the hardener powder has been incorporated. Apart from fast curing (after only 45 minutes), IKO metatech Detail is also characterised by rapid installation, as the second layer is applied wet-on-wet to the first layer.

IKO 110 sgm Polyester Fleece.

Guidance for specification option:

A reinforcement fleece consisting of non-woven polyester with a density of 110 g/m². This fleece is rolled out in the wet first layer of IKO metatech Detail and pressed in areas that are subject to heavy footfall. It therefore ensures the strength, stability and longevity of the system.